Get free quotes

Free calculator

Rolling sphere calculator: what does one air rod or mast protect?

Choose the protection class and the height of the rod or mast. The calculator rolls the sphere for that class over the tip and shows how far out it protects at ground level and at the height of your roof, then sizes the mesh and down conductors for the building.

Rolling sphere and air rod calculatorHow far an air rod or mast protects at each height, plus mesh and down conductors
Sheet
RSC-01
Method
r 20 to 60 m

The figures update as you type. A guide for planning and briefing, not a design.

Drawing

Sphere radius R
-
Protected radius at ground
-
Protected radius at roof height
-
Roof mesh, max
-
Down conductors and earths
-
Your object
-

The rolling sphere method is how lightning protection designers decide where air terminals go. Imagine a sphere rolled over and around the building: anywhere the sphere can touch can be struck and needs an air terminal; anything the sphere cannot reach is protected. The sphere's radius depends on the lightning protection level: 20 m for class I, 30 m for II, 45 m for III and 60 m for IV.

How the zone is worked out

For a single vertical rod or mast of height h, the sphere of radius R rests on the tip and on the ground. Its centre sits at height R, a horizontal distance of √(h(2R minus h)) from the rod. Everything under the curve of the sphere is protected. At a height y above the ground the protected radius is r(y) = √(h(2R minus h)) minus √(y(2R minus y)). If the rod is taller than the sphere radius, only the bottom R metres count, and the side of a very tall mast can itself be struck.

That is why a mast for a thatched house stands well clear of the roof and is tall enough that the whole thatch, including the ridge and the chimney, sits inside the curve. The calculator draws the curve and shows a building of your chosen height and distance under it.

Mesh and down conductors

On flat and low pitched roofs, designers often use a mesh of conductors instead of, or as well as, air rods. IEC 62305-3 gives the maximum mesh size for each class: 5 x 5 m for I, 10 x 10 m for II, 15 x 15 m for III and 20 x 20 m for IV. Down conductors are spaced around the perimeter at typical distances of 10 m for classes I and II, 15 m for III and 20 m for IV, with at least two on any building, each ending in an earth electrode with a test joint.

Using the result

The numbers here are a starting point for a conversation with a designer, not a design. Real roofs have ridges, chimneys, aerials, solar arrays, parapets and plant, each of which the sphere must be rolled over, and isolated systems for thatch also need the right separation distance (see the separation distance calculator). Ask for a layout drawing to SANS 62305-3, and see lightning rods, lightning masts and down conductors.

Frequently asked questions

Does a taller rod always protect more?
Only up to the sphere radius. Once the rod is taller than R (20 m for class I, 60 m for class IV), the protected radius at ground level stops growing, and the sides of the rod above that height can be struck.
Which class should I pick?
Class IV is the minimum, class I the highest. A risk assessment sets the class; many homes come out at III or IV, while thatch, schools, hospitals, fuel sites and buildings with many people often go to I or II. If you are not sure, try class II and III to see the difference.
What about the protection angle method?
IEC 62305-3 also allows a protection angle method for simple shapes, which gives a cone around the rod. The angle shrinks as the rod gets taller and it does not apply above the sphere radius. The rolling sphere works for any shape, which is why designers usually use it.

Sources

Formulas and table values as published in these standards and papers. The calculators simplify them for a first look; a designer applies the full method.

More calculators

Free quote request, no obligation

Request quotes for lightning rods

Fill in the survey sheet the way an installer would on a first visit: the size and height of the building, the roof and the protection class if you know it, or simply how many arresters, plugs, spikes, metres or visits. Installers and suppliers in your area quote you directly.

Site survey sheetLightning Rods and Air Terminals
Sheet
93139
Date
2026-11-21
Scale
NTS

1The job

2How many (optional, it helps the quote)

Your ordernot to scale

-
-
-
-
-
-
Estimate
-

Geometry and the standard's table figures for the request, not a design.

3Where you are now

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: rods, masts, arresters, spikes, tape or services.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable installers, electricians, engineers and suppliers. See our privacy policy.

Get free lightning protection quotes