Get free quotes

Free calculator

Earth spike resistance calculator: how many rods reach 10 ohms?

Choose the soil, or enter a measured resistivity, the rod length and diameter, and how many rods you will drive and how far apart. The calculator gives the resistance of one rod, of the group, and how many rods a 10 ohm target needs.

Earth spike resistance calculatorResistance of one or more earth rods in your soil, and how many reach 10 ohms
Sheet
EEC-01
Method
10 Ω

The figures update as you type. A guide for planning and briefing, not a design.

Drawing

One rod
-
Your group of rods
-
Rods in a row for the target
-
Against the target
-

Every down conductor ends in an earth electrode, and the lower its resistance, the more easily the strike current spreads into the ground. IEC 62305-3 recommends a low resistance, under 10 ohms where possible, for the common type A arrangement of rods at each down conductor. Soil is the biggest variable: the same spike can read 20 ohms in wet clay and several hundred in dry sand or on rock.

The formulas

One rod. R = ρ / (2πL) x [ln(8L / d) minus 1], where ρ is the soil resistivity in ohm metres, L the driven length in metres and d the rod diameter in metres. This is the Dwight formula used in BS 7430 and IEEE 142.

Rods in a row. Rods close together share the same soil, so two rods are not half the resistance of one. BS 7430 gives Rn = R1 x (1 + λα) / n, with α = ρ / (2π R1 s) for a spacing s, and λ from 1.00 for two rods to 3.81 for ten in a straight line. The rule of thumb is to space rods at least as far apart as they are long.

Typical soil resistivity

The presets use typical values: clay and loam about 50 ohm metres, sandy clay about 150, sand and gravel about 500, dry sand about 1,500 and rock or weathered granite about 3,000. Real soil varies with depth, moisture and season, and Highveld soils dry out in winter. For a design, measure the resistivity on site with a four-pole (Wenner) test and test the finished electrodes. See earth resistance testing.

When rods are not enough

On rock or very dry sand, adding rods quickly stops helping. Installers then use deeper driven rods, a ring earth electrode (a buried conductor around the building, type B), earth enhancing compound, or a combination. Ask your installer which they propose, and see earth spikes, earthing materials and earthing installation.

Frequently asked questions

Is 10 ohms a legal requirement?
IEC 62305-3 recommends a low earth resistance, under 10 ohms where possible, for lightning protection electrodes. The electrical installation's own earthing has its own requirements under SANS 10142-1. Your designer or electrician will say what target applies.
Why doesn't doubling the rods halve the resistance?
The rods share the same soil, so their zones of influence overlap. The closer they are, the more they overlap. Spacing them at least one rod length apart keeps most of the benefit.
How accurate is the calculator?
As accurate as the resistivity you put in. With a typical soil value, treat the answer as a guide to the order of magnitude. With a measured resistivity it is a fair design estimate, but the finished electrode must still be tested.

Sources

Formulas and table values as published in these standards and papers. The calculators simplify them for a first look; a designer applies the full method.

More calculators

Free quote request, no obligation

Request quotes for earth spikes

Fill in the survey sheet the way an installer would on a first visit: the size and height of the building, the roof and the protection class if you know it, or simply how many arresters, plugs, spikes, metres or visits. Installers and suppliers in your area quote you directly.

Site survey sheetEarth Spikes and Earth Rods
Sheet
85622
Date
2026-11-21
Scale
NTS

1The job

2How many (optional, it helps the quote)

Your ordernot to scale

-
-
-
-
-
-
Estimate
-

Geometry and the standard's table figures for the request, not a design.

3Where you are now

4Your list (optional)

  1. 01
  2. 02
Up to 12 lines: rods, masts, arresters, spikes, tape or services.
Needs and options

5Your details

Free and no obligation. By sending you agree that we may share your request with suitable installers, electricians, engineers and suppliers. See our privacy policy.

Get free lightning protection quotes